...
Automotive lighting manufacturer · OEM & ODM · Wholesale+86 13434569328jack@sunshinyled.com
Home/Blogs/Article

How to Replace a License Plate Light (Bulb and Housing)

Short answer: To replace a license plate light, confirm the bulb type, turn the lights on to see which side is out, remove the lens or cover, pull or twist out the old bulb, fit the new one and test it before you close the cover. Most cars use a small wedge bulb (T10, W5W, 194 or 168) or a festoon bulb, and the job takes about ten minutes with a screwdriver. If the lens is cracked or the socket is corroded, replace the whole housing.

Key takeaways

  • Check the bulb type first: the owner’s manual or the old bulb’s marking tells you whether it is a wedge, festoon or bayonet bulb.
  • Switch the lights off before you touch the bulb, and do not overtighten the cover screws, because the lens cracks easily.
  • LED wedge bulbs can be polarity sensitive. If a new LED does not light, remove it, turn it 180 degrees and test again.
  • US federal rules require the license plate lamp to be white, steady and lit with the headlamps, so do not fit colored bulbs.

Which bulb does your license plate light use?

Most license plate lights use one of three bulb types: a wedge, a festoon or a bayonet. Look in the owner’s manual, or pull the old bulb and read the marking on it. The table shows the common types and how they fit.

Bulb type Also called How it fits How to remove it
Wedge T10, W5W, 194, 168 Flat glass base pushed into a socket with two side contacts Pull it straight out
Festoon C5W, 31, 36, 39 or 41 mm Pencil-shaped glass with a metal cap at each end, held between two clips Pry one end out of its clip
Bayonet BA9S Round metal base with two small pins Push in and twist a quarter turn

Festoon bulbs come in several lengths, so measure the old bulb or check the manual before you buy. A bulb that is a few millimeters too short or long will not sit properly in the clips.

Wedge, festoon and bayonet license plate bulbs lined up on a workbench for comparison

What do you need to replace a license plate light?

You need a replacement bulb of the right type, a small screwdriver and, if the lens is clipped in, a plastic trim tool. Keep the list short, because the job is simple.

  • Replacement bulb: the same base and voltage as the old one. Buy two so both sides match.
  • Screwdriver: Phillips or flat, depending on the cover screws.
  • Trim tool or flat blade: for covers that snap out. Wrap the tip in tape to avoid scratching paint.
  • Gloves and a clean cloth: handle glass bulbs by the base, and wipe the lens before you refit it.

How do you replace a license plate light bulb step by step?

Work from the outside in, and test the new bulb before you refit the cover. The steps are the same for most cars and trucks.

  1. Find out which bulb is out. Turn on the headlights or parking lights and check both sides from behind the car. Then switch everything off.
  2. Open the cover. Remove the small screws holding the lens, or press the release tab and pry it out. On some trucks the socket twists out from behind the bumper or tailgate.
  3. Remove the old bulb. Pull a wedge bulb straight out, release a festoon bulb from its clips, or twist a bayonet bulb a quarter turn.
  4. Check the socket. Look for green or white corrosion, melted plastic or bent contacts, and clean light corrosion with a dry brush or a contact cleaner.
  5. Fit the new bulb. Push it in until it seats. Do not touch the glass of a halogen-type bulb with bare fingers.
  6. Test it. Turn on the lights and check that the plate is lit evenly from behind the car.
  7. Refit the cover. Tighten the screws until they are snug and stop. Overtightening cracks the lens and lets water in.

How do you replace the whole license plate light housing?

Replace the whole housing when the lens is cracked, the housing has filled with water or the socket is corroded beyond cleaning. A new housing is usually a small part and ends repeat failures.

  1. Remove the lens and the bulb as above.
  2. Unplug the wiring connector by pressing its latch. Do not pull on the wires.
  3. Take out the housing by removing its screws or releasing its clips from the bumper or plate panel.
  4. Fit the new housing in the same place, plug in the connector and fit the bulb.
  5. Test the lamp, then close the cover and check that the seal sits flat against the panel.

License plate light housing removed from a bumper with the wiring connector unplugged

Can you use an LED bulb in a license plate light?

Yes, most license plate lights accept LED replacements, but check the base and the polarity. The lamp has to light the plate, not just glow: FMVSS No. 108 requires an illumination value of no less than 8 lux at each test location on the plate (49 CFR 571.108, S7.7.13.2), so a dim or badly aimed bulb is a poor choice.

  • Base type: match the wedge, festoon or bayonet base and the festoon length.
  • Polarity: many LED wedge bulbs only work one way around. If the bulb stays dark, flip it and test again.
  • Bulb-out warnings: some cars check the current of each lamp, and a low-draw LED can trigger a warning. A Canbus-ready or load-matched bulb avoids it. See our guide to Canbus vs non-Canbus LED bulbs.
  • Color: use white. The same standard lists the license plate lamp as white in its equipment table.

What if the new bulb does not work?

If a new bulb stays dark, check the polarity, the socket and the fuse, in that order. The table links each symptom to the likely cause.

Symptom Likely cause What to do
New LED does not light Reversed polarity Remove the bulb, turn it 180 degrees and test
Bulb lights, then goes out Corroded or loose socket contacts Clean the contacts or replace the housing
Both sides are out Blown fuse or a shared wiring fault Check the tail lamp fuse and the connector
Bulb-out warning on the dash LED draws less current than the car expects Use a Canbus-ready or load-matched bulb
Light flickers Loose bulb or damaged wiring Re-seat the bulb and inspect the wiring near the housing

Is a broken license plate light illegal?

A license plate light that does not work can fail an inspection or earn a ticket in many places, but the exact rule depends on your state or country. The federal equipment standard sets what the lamp must do: the table in FMVSS No. 108 lists the license plate lamp as white and steady burning, lit when the headlamps or parking lamps are on, and the standard defines it as a lamp “used to illuminate the license plate on the rear of a vehicle” (49 CFR 571.108). Check your local rules for fines and inspection requirements.

What should distributors stock for license plate lights?

Stock wedge bulbs and festoon bulbs in the common lengths, and sell them with clear fitment notes. Most returns come from the wrong base, the wrong festoon length or an LED fitted the wrong way around.

  • Wedge bulbs: T10 / W5W / 194 / 168 cover most license plate positions.
  • Festoon bulbs: stock 31, 36, 39 and 41 mm, because the length decides the fit.
  • Polarity: choose non-polar models where possible, so customers do not need to flip the bulb.
  • Canbus models: keep a Canbus-ready option for cars that show a bulb-out warning.
  • Packaging: print the base type and size on the box so the customer can match it to the old bulb.

How TUHO supplies this category

TUHO lists license plate bulbs in its license plate light range, grouped by chip series. Two examples from the live catalog:

  • New Series T10 / W5W / 194: the page lists 7 models, with Canbus and non-polar versions marked in the table.
  • COB festoon: the page lists 8 models in 31, 36, 39 and 41 mm and C5W sizes.

The figures are as listed in the factory catalog, so confirm the model you need before ordering. Documents and approvals are confirmed per model and per order.

Sourcing license plate bulbs for your range? TUHO supports OEM/ODM, custom logo and packaging, mixed-SKU orders and sample testing. Request a quote

FAQ

How long does it take to replace a license plate light?

Replacing a license plate light usually takes about ten minutes on most cars. A cracked lens or a corroded housing takes longer because the whole unit has to come out.

What bulb does a license plate light use?

A license plate light usually uses a T10 or W5W wedge bulb, a festoon bulb or a bayonet bulb. Check your owner’s manual or the marking on the old bulb, because the base and the length must match.

Why won’t my new license plate bulb light up?

A new license plate bulb that won’t light is most often an LED fitted the wrong way around, a corroded socket or a blown fuse. Flip the bulb 180 degrees first, then clean the contacts and check the fuse.

Can I replace a license plate bulb with an LED?

Yes, you can replace a license plate bulb with an LED if it matches the base and gives enough light to illuminate the plate. Use white, and choose a Canbus-ready bulb if the car shows a bulb-out warning.

Do I need to replace both license plate bulbs at once?

You do not have to, but replacing both gives a matching light and saves a second repair. The remaining old bulb is likely to fail soon after.

Bottom line: Find the bulb type, switch the lights off, swap the bulb, test, and refit the cover without overtightening. If the lens or socket is damaged, replace the whole housing.

Editorial note: Equipment requirements were checked in November 2026 on the eCFR (49 CFR 571.108, definitions, S7.7.13.2 and Table I-a). Local inspection rules and fines vary and were not checked. Product details come from the TUHO New Series T10 and COB festoon pages.

On this page
    Get a free quote

    Wholesale LED headlight bulbs & OEM/ODM — reply within 24h.

    ✓ Reply within 24h✓ No spam✓ B2B only

    Related articles

    滚动至顶部
    TUHO Lighting team meeting with international buyers
    TUHO Lighting

    Let's talk about your next order.

    Tell us your sockets, quantity and market. We reply with a quotation.

    • OEM & private label
    • 2-year warranty on headlight bulbs
    • Standard items ready in 1–10 working days
    Get a Quote

    Request a quotation

    Leave your details and we will get back to you.

    Your inquiry list

    0 models · we reply within one business day

    MOQ1 carton per model
    SamplesTest before bulk order
    OEMYour logo & packaging

    Your details

    We quote the whole list in one reply.

    Your information is kept confidential and used only to prepare your quotation.

    Prefer chat? WhatsApp us